MoJack XT Mower Lift For Tractors & Zero Turns Up To 500 Pounds

This lift is very heavy duty and comes almost completely assembled. 20 minutes after receiving it I had my zero turn mower up in the air changing the blades.

Easy to assemble and very useful. I use the lift on a 42 inch Toro Zero Turn riding mower. There are a few drawbacks. Using a 19.2 volt drill in place of the manual crank could be a little dangerous at either extreme. One needs to use the other hand to keep the locking pin from engaging thus you are bending oven and greatly reducing wrist strength and could torque your wrist if the chock slips on the 3/8 in bit.

I recommend using the lift screw handle. The two front-wheel hold-down straps do not work with the smaller front tires and needed to be modified. Also, If the lift is raised to the max a wood block should be placed under the rear bagger bracket so that it does not dig into the ground. Having said all that I still think it is a very useful tool for working under the cutting deck. I also bought the push mower table which works great.

Easy to assemble and very useful. I use the lift on a 42 inch Toro Zero Turn riding mower. There are a few drawbacks. Using a 19.2 volt drill in place of the manual crank could be a little dangerous at either extreme. One needs to use the other hand to keep the locking pin from engaging thus you are bending oven and greatly reducing wrist strength and could torque your wrist if the chock slips on the 3/8 in bit.

I recommend using the lift screw handle. The two front-wheel hold-down straps... more

Easy to lift mower, however getting wheels properly positioned is problematic. When driving mower onto the wheel pans, the whole MoJack wants to scoot along in front of my mower. My solution is to place a long board (piece of 2x8 about 3 feet long) between the MoJack and the wall so it cannot move. They probably should have non skid pads installed, I did not look to see about that, but if they have any they are small and ineffective.. Other than that I like the MoJack.

The device works great. It's easy to use, safe, and doesn't take up a lot of storage space. If you have a lawn or garden tractor, it's a must-have tool!

Got this in a couple days of ordering and had it put together in 1/2 hr. Product is strong & sturdy. I used this on my 61"deck Ferris Zero turn Commerical tractor and it works great. I only wish I would have bought this at the beginning of the season and not at the end of the mowing season.

I recently bought a RZT L42 Cub Cadet O Turn mower. I bought the jack so that I would not have to remove the mower deck to sharpen or replace the blades. It works very well for that. I am sure that I will find other uses for It. It is a very strong jack. The Cub Cadet's front wheels are 10".Anything smaller will not work.

Ordered to use on our Z645 Deere. We sometimes mow before the dew has left the grass, and mow deck gets plugged. Used to use floor Jack and stands, but wanted one of these to make it quicker and easier. Jack works great and stores easily.

I found I have more room while cleaning deck or changing blades than I did with floor jack and stands. Shipping was very quick and this company is great to deal with. Will make more purchases in the future. You better get you one of these.

It does what I needed it to lift my Scag Turf Tiger Zero Turn.

I am a new owner of an EXmark zero turn and it can do wonders in record time. The only problem was trying to get access under the deck. The single pole jack was just not reliable and safe enough for me even though it was cheaper. But when the purchase of the Mojack arrived, I knew it was going to be Christmas in July. This item is heavy but it can handle whatever you have and makes you feel safe and secure while servicing your big boy toys.

After years of laying on the ground taking the deck off to sharpen, clean, or change blades I realize this is what I should have done years ago. I am getting old and my joints are wore out to the point I could not do this job without this jack.

Great for any maintenance on front end - cleaning under deck, changing blades re- adjusting rollers. Saves time and energy. Better than trying shade tree methods.